PAYMENT

ECU Tune Stage 1

MWM hand-held module for Mercedes x253 Facelift GLC63
схема
схема

about the function

схема (1)

Today’s engines are controlled electronically using software.  ECU Tune accesses this software via specially modules in order  to bring maximum performance when you want it and retain the comfort of a daily driver when you don’t need it.

The MWMods ECU Tune  is a user-friendly device, it stores both MWMods Stage1 file and your vehicles STOCK firmware file and allows an unlimited ability to switch between firmwares . The module plugs directly into the OBD2 port and delivers the Stage1 file to the ECU, programming usually takes 1-3 minutes. The power increase is achieved by adjusting such parameters of the engine control unit as air/fuel ratio, ignition timing , throttle mapping and  boost pressure  for turbo-charged vehicles.
MWMods ECU software is developed on the dyno and verified with multiple runs and logs.

ECU upgrade for the Mercedes M177 engine offers huge gains in performance across the entire RPM range without sacrificing around town comfort or daily driver reliability.

Stage1 Most Wanted Mods:
– Software changes only , no physical interventions.
– The priority is the resource.
– Maintenance of the stock version = maintenance of the tuned version.

 

Please refer to the picture below to view the power increase figures for your Mercedes  X253 Facelift GLC63(s) V8 BiTurbo

Video description

схема (1)

payment

схема (1)
Loading file
  • Fullscreen
  • Wireframe
  • Zoom In
  • Zoom Out
  • Rotation
  • Screenshot
  • Help

Controls

×
  • Rotate with the left mouse button.
  • Zoom with the scroll button.
  • Adjust camera position with the right mouse button.
  • Double-click to enter the fullscreen mode.
  • On mobile devices swipe to rotate.
  • On mobile devices pinch two fingers together or apart to adjust zoom.
  • On mobile devices 3 finger horizontal swipe performs panning.

ECU Tune Stage 1

1,050.00 $

Other Mods for your Mercedes below could be recorded on a tune module.

If you order 5+ Mods, there is a 10% discount.

TOTAL COST:

1200$

reviews

схема (1)

frequent questions and answers:

MWMods warrants to the consumer that all of our hardware will be free from defects in material and workmanship for a period of a year from date of the original purchase. Before sending a hand-held tuner , we check VIN of a vehicle in order to exclude the possibility of a mistake. If the module works first time , it will work all the time. However, if suddenly stops working, we ask for a video and a photo to make sure that there are no external damage.
No , MWMods hand-held tuner won’t add neither pops nor crackles because it doesn’t disable any engine protection systems. 

There is no need to keep the module plugged in all the time. You can remove the module after ECU upgrade

still having questions?

ASK US A QUESTION
схема (2)

INSTRUCTION:

схема (1)

Please read all directions before beginning.

 

Prepare the Car: 

The car must be put into programming mode first

Make sure the car is warm and everything is stable

Make sure the car battery is fully charged

Turn off accessories and unplug any SD or USB devices

Don’t change any settings or press any buttons while programming

The car must be in IGNITION position 2 (all cluster leds are ON but the motor is OFF)

Be Patient in this process, wait a minimum of 60 seconds until the audio head has totally booted up. 

 

Begin Installation:  

– switch IGNITION ON (2 click clockwise) or 2 presses of Start/Stop button and make sure you see all cluster LEDS are ON

– wait till your audio head unit totally booted (60 seconds)

– plug module to the OBD2 (diagnostic socket) under the dash and observe the blinking green light on one side of the module
– wait 1-3 minutes before the light stop totally blinking
– installation is finished, unplug the module, ignition off.

You may get an error message in the service screen, for example “Mercedes Connect inoperable” or “Lights are Defective, consult workshop”.  You may note the clock has reset to 12:00. Turn the car off, wait a minute, turn it back on, the messages will clear.

 

Important: Do not leave the module on the OBD connector. Use the module only when you want to switch between Stage1(2) and factory maps.

 

In addition to the module you will find an SD card on which the factory map is recorded. The SD card from Stage1(2) is already installed in the module. In order to install the Stock map, replace the SD cards and repeat the installation process. Below are instructions on how to disassemble the module:

– open the box with the knife. Do not put the knife more than 2-3mm. Open OBD tune box from the long side not to damage electronics) 

– remove the microSD card (just pull it out)

– plug the second microSD card to the socket

– then repeat all actions you did the first time when downloading the Stage1(2) file. 

CONTACTS:

схема (1)

Instagram

Facebook

Youtube

WhatsApp

Email

TEXT US
© 2021-2023 Most Wanted Mods
Artsiom Shamailau
Address: Lanciego 10G
ID №225442836 from 18.01.2018
Phone: +1 (646) 285 8841
e-mail: info@mwmods.com