COMAND:
This is a two step process, you will be plugging and unplugging the MWMods’ module twice. Please read all directions before beginning.
Prepare the Car: The car must be put into programming mode first. Make sure the car is warm and everything is stable. Turn off accessories and unplug any SD or USB devices. Don’t change any settings or press any buttons while programming.
The car must be in IGNITION position 2 (all cluster leds are ON but the motor is OFF)
Go to Youtube and watch this video first – this is the video showing “IGNITION POSITION 2”.
Be Patient in this process, wait a minimum of 60 seconds until the audio head has totally booted up. THIS WILL TAKE AT LEAST A FULL MINUTE.
You are ready.
Now, plug the module to the OBD2 diagnostic socket under the dash. The COMAND screen will blank and you will see some small white lettering….
There are two programs.
“Step 1: Backup+revert factory” – this program tests the car for coding possibility and stores the original codings to file, if you were to run it again – it will revert to the factory settings.
Turning the controller will bring you to….
“Step 2: SA628 Activation – this one will activate IHC+ SA628 (the Multibeams) at your car.
Begin Installation: Using the controller, rotate or use << >> buttons to select the first script:
Step1: Backup+revert factory and confirm pressing the controller down or * star button.
This will begin the program…watch the progress bar until you see: “remove the module now” This takes about 1 minute or so. Be Patient, don’t remove module until you see that message on screen. When you do, and only when you do, remove the module.
IMPORTANT: If at the end of this step, you see a message “Exception, see the logfile” – DO NOT RUN STEP 2 !!! Contact us as below.
After completing Step1, plug the Module back in. The screen will again go blank with small white letters-scroll to “Step2:SA628 Activation” and again confirm pressing the controller down or * star button.
The program will install. Observe the progress bar till you again see: “remove the module now” – this takes about 1-3 minutes depending on the car model. (sometimes it seems that it freezes at certain percentage – just wait, it is working). You may see the COMAND screen re-boot, don’t do anything yet, wait.)
When the program is finished, you will see the message “Successful SA628 On 1”- then remove the module when instructed on the COMAND screen.
Never remove the Module unless the Comand screen tells you to.
You may get an error message in the service screen, for example “Mercedes Connect inoperable” or “Lights are Defective, consult workshop”. You may note the clock has reset to 12:00.
Don’t panic !
Turn the car off, wait a minute, turn it back on, the messages will clear.
Possible issues: If you see “Exception, see the logfile” – remove the module, open the box and send me the LOGFILE.LOG located at the microSD – then I will let you know what is wrong and we will fix this. When the script successfully runs, but something does not work as expected – then also send me the logfile.
MBUX:
This is a two step process, you will be plugging and unplugging the tuneOBD module twice. Please read all directions before beginning.
Prepare the Car: The car must be put into programming mode first. Make sure the car is warm and everything is stable. Turn off accessories and unplug any SD or USB devices. Don’t change any settings or press any buttons while programming.
The car must be in IGNITION position 2 (all cluster leds are ON but the motor is OFF)
Go to Youtube and watch this video first – this is the video showing “IGNITION POSITION 2”.
You are ready.
Now, plug the module to the OBD2 diagnostic socket under the dash.
When the program is finished, you will see no longer flashing green light, then remove the module from OBD port
Never remove the Module unless the the green light stop flashing.
Before testing the new features, you need to configure the vehicle
– select AUTO at the light rotary switch
– push the high beam lever forward and see white high beam with (A) sign at the cluster+blue high beam sign
Follow few steps to put new files. The first open the module. Check Youtube video on how to open the module in the most gentle way possible. The archive files (3) must be copied to the SD card inside the module. Use your notebook on Windows and SD card-reader. Format the SD card to FAT32 before recording files.
filename !FIRMWARE.LDR start with ! and this is not the mistake
If you are using an Apple Mac, follow simple steps according the video. Windows users do not need to follow this video.
Carefully plug SDcard back to the module and close it with cover.
Reviews
There are no reviews yet.